Dyson Stick Vacuum Service

If you want your Dyson stick vacuum to maintain cleaning performance, it’s essential to regularly service the vacuum. Over time, filters clog, brush rollers accumulate debris, and internal components wear down, leading to reduced performance. This step-by-step guide outlines the complete servicing process, from filter replacement and power head cleaning to final testing, ensuring your Dyson functions like new. This applies to Dyson V6, V7, and V8 stick vacuum cleaner models.

What parts do you need?

We sell high-quality replacement parts to ensure long-lasting and effective repairs! You can also check the schematic page for this vacuum cleaner.

How do I know when to...

Service My Dyson Stick Vacuum?

Pulsing

If your Dyson stick V6, V7, or V8 vacuum cleaner is pulsing, that usually means you need to service your machine.

Low Performance

Over time, the filters, brush roll, and cyclone on your Dyson stick become dirty or worn. Cleaning or replacing these will improve performance.

Odor Issues

Is your Dyson stick vacuum starting to smell? If so, you need to service your Dyson and likely replace the filters.

Let's get down to business...

Step-by-Step Repair Guide

Step 1: Inspect and Disassemble the Vacuum

Remove the Canister: Start by emptying the canister and then detach it from the vacuum body using the clip located near the bottom. Once removed, check for any obstructions or debris inside the canister. If necessary, blow out any debris with compressed air.
Detach the Cyclone: Next, remove the cyclone from the motor housing by pressing the buttons on either side and sliding it up. The cyclone should now be separated from the motor housing.
Inspect the Cyclone: Take a look inside the cyclone for any buildup of debris. Often, you’ll find dust and other particles stuck inside, which can impede airflow. You can demonstrate this by tapping the cyclone gently to release some of the trapped dust.
Clean the Motor Housing: Inspect the motor housing for any fine dust that may have bypassed the cyclone. This dust can cause the motor to retain heat and run warmer, so it’s important to clean it out thoroughly.

Step 2: Clean the Components

Blow Out the Cyclone and Motor Housing: Take both the cyclone and motor housing outside and use an air compressor to blow out any trapped debris. This step is crucial for maintaining proper airflow and preventing overheating.
Clean the Power Head: Regular maintenance of the power head is essential for optimal performance. Start by removing the brush roll using a large flathead screwdriver or a coin. Inspect the area around the brush roll for any buildup of hair or debris.
Remove Debris: Use a pick or a small brush to remove any debris from inside the power head. While this vacuum wasn’t too dirty, it’s common to find significant debris buildup, especially in machines that haven’t been serviced regularly.
Clean the Brush Roll: Once the brush roll is removed, clean it thoroughly. If there’s any hair wrapped around it, use a pair of scissors or a razor blade to cut it away. You can also use isopropyl alcohol to clean any remaining grease or dirt.
Lubricate the Brush Roll Bearing: If necessary, apply a small amount of grease around the brush roll bearing to prevent future lock-ups, especially if you have pets.
Clean the Exterior: Use denatured alcohol to remove any paint scuffs or marks on the vacuum’s exterior. Be aware that denatured alcohol can leave a white residue, so follow up with an all-purpose cleaner to remove any leftover film.

Step 3: Reassemble and Final Check

Reattach the Cyclone and Canister: Snap the cyclone and canister back into place on the vacuum body.
Reinstall the Brush Roll: Put the brush roll back into the power head and ensure it spins freely.
Final Inspection: Give the vacuum one last inspection to ensure everything is in working order. If you have an air compressor, use it to blow out any remaining dust from the vacuum’s interior.
Test the Vacuum: Turn the vacuum on and check for any issues. If it’s still pulsing, consider replacing the filter, as it may be the cause of the problem.

You also might need...

Other Items for This Repair

While completing this repair, you should check these other important items on your vacuum cleaner to ensure the best possible performance and longevity!

Final Thoughts

Servicing your Dyson V8 stick vacuum regularly is key to maintaining its performance and longevity. While this guide covers the basic steps, if you prefer not to handle the maintenance yourself, feel free to bring your vacuum to one of our locations. We offer comprehensive service packages that include everything outlined here and more.

Need More Stuff?

We offer comprehensive part diagrams and repair tutorials to help you keep your vacuum running at its best. VacuumsRus is your one-stop-shop for anything vacuum cleaner related!

Schematics and Parts Diagrams

You can find the schematics for each model this repair is applicable to here:

How to Service a Dyson V6, V7, and V8 Stick Vacuum – Dyson Repair Guide